I-war IAX2 support

Discussion:

I-war IAX2 support

iWar (wardialer for Unix) mailing list.

2009-01-14 21:37:16 UTC

I'm curious if IAX is fully functional now or not. All of my test calls
placed over IAX2 timeout, despite
the debug logs denoting the calls being answered:

DEVICE ID=0 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 (hw:0,0) CAPS=7
DEVICE ID=1 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 - MIC ADC (hw:0,1)
CAPS=1
DEVICE ID=2 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 - MIC2 ADC (hw:0,2)
CAPS=1
DEVICE ID=3 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 - ADC2 (hw:0,3)
CAPS=1
DEVICE ID=5 NAME=front CAPS=6
DEVICE ID=6 NAME=default CAPS=3f
DEVICE ID=7 NAME=dmix CAPS=6ne and successfully dials and the call goes
IAXCLIENT: Originating an audio only call warning: The VAD has been
replaced by a hack pending a complete rewrite
IAXCLIENT: Failed video codec negotiation.
IAXCLIENT: Call 0 acceptedtil it times out like it is recieving no data.
Any
IAXCLIENT: Call 0 ringing
IAXCLIENT: Call 0 progress
IAXCLIENT: Call 0 answered
IAXCLIENT: Call disconnected by remote

I've tried this on 3 different systems, one with iaxclient-2.1beta3 and two
with iaxclient-2.0.2, all with the same effect. (I'm using iwar from
CVS). I'm under the impression
that this _did_ work, based on the following URL.

http://www.digitalbond.com/index.php/2007/03/07/assessing-modems-with-iwar-voip-mode/

Thanks,

madsara

iWar (wardialer for Unix) mailing list.

2009-01-15 00:23:59 UTC

Permalink

I've IWAR 0.71 working fine in the Backtrack 2 distro believe it or
not. I'll throw up some instructions when I'm back in the nest'

Post by iWar (wardialer for Unix) mailing list.
I'm curious if IAX is fully functional now or not. All of my test calls
placed over IAX2 timeout, despite
DEVICE ID=0 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 (hw:0,0) CAPS=7
DEVICE ID=1 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 - MIC ADC (hw:0,1)
CAPS=1
DEVICE ID=2 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 - MIC2 ADC (hw:0,2)
CAPS=1
DEVICE ID=3 NAME=Intel 82801DB-ICH4: Intel 82801DB-ICH4 - ADC2 (hw:0,3)
CAPS=1
DEVICE ID=5 NAME=front CAPS=6
DEVICE ID=6 NAME=default CAPS=3f
DEVICE ID=7 NAME=dmix CAPS=6ne and successfully dials and the call goes
IAXCLIENT: Originating an audio only call warning: The VAD has been
replaced by a hack pending a complete rewrite
IAXCLIENT: Failed video codec negotiation.
IAXCLIENT: Call 0 acceptedtil it times out like it is recieving no data.
Any
IAXCLIENT: Call 0 ringing
IAXCLIENT: Call 0 progress
IAXCLIENT: Call 0 answered
IAXCLIENT: Call disconnected by remote
I've tried this on 3 different systems, one with iaxclient-2.1beta3 and two
with iaxclient-2.0.2, all with the same effect. (I'm using iwar from
CVS). I'm under the impression
that this _did_ work, based on the following URL.
http://www.digitalbond.com/index.php/2007/03/07/assessing-modems-with-iwar-voip-mode/
Thanks,
madsara
_______________________________________________
Iwar mailing list
http://bundy.vistech.net/mailman/listinfo/iwar

iWar (wardialer for Unix) mailing list.

2009-01-15 05:30:14 UTC

Permalink

Have you tried using just the iaxclient and seeing if that works? (ie:
compile iaxclient, load the softphone and try dialing)

Remember, most open source development built on other libraries usually
means going to the source for support. All iWar does is tie into the
iaxclient library and controls dialing. Audio should still pass through
the same functions as the original iaxclient.

just curious
-jf